Home > LS Tractor Parts >

Toothbar For 'LS' C, G, R, S, XR Series Tractors w/66" 'LS' Buckets
Toothbar for 'LS' Buckets

More Views:

Our Price: $470.00

Availability:: Usually Ships in 3 to 5 Business Days


8 Tooth Toothbar for 'LS' C, G, R, S, XR Series Tractors with 66" Buckets.

WE HAVE SOLD HUNDREDS OF THESE TOOTHBARS & HAVE HAD 100% CUSTOMER SATISFACTION! There Are Many Makes & Styles of Toothbars for Sale - Many of Them Homemade. But with Forged, Long Shanked Teeth, Replaceable Tips and Professional Fabrication Quality, Expect These to be the BEST!

  • 66" is the 'Nominal' Bucket Size. This Toothbar will fit inside the 66" 'LS' Bucket!
  • Toothbar Attaches Easily to the Loader Bucket:
    • Each of the Tooth Shanks Have 'V' Notches On the Bottom That Fits Tightly Over The Front Cutting Edge of The Bucket - This is Where All The Pushing Pressure is Applied.
    • The 'V' Notches Have a Maximum Opening of 5/8" and Tapers Down to a Point. Therefore, the Maximum Recommended Thickness of the Bucket Cutting Edge Suitable For These Toothbars is About 1/2".
      • This Toothbar Will Work Only on Original 'LS' Buckets with Weld-On Cutting Edges, Because Bolt On Cutting Edges Are Usually Thicker Than 1/2".
    • Each End of the Toothbar has a Mounting Flange with a Slotted Hole for the Attaching Hardware to Fit Through. You'll Need to Drill One Matching Hole on Each End of the Bucket's Sidewall and Bolt the Toothbar on with 5/8" or 3/4" Diameter Bolts - Length as Required.
      • We Market These Toothbars as 'NOT INCLUDING THE ATTACHING HARDWARE' (Bolts, Nuts & Washers). However, the Toothbars Do Ship With The Hardware, But Too Often the Hardware Gets Lost in Shipping, So if You Get the Hardware With Your Toothbar, Consider it an Extra!
  • Toothbar Extends Back Into the Bucket by About 6" (from the front of the bucket's cutting edge) and the Teeth Extend Beyond the Front of the Bucket by about 6".
  • The Width of the Toothbar Will Be Fractionally Narrower Than the Bucket's Inside Width. You can Fill This Gap with Washers/Spacers, But It Isn't Necessary to.
  • The Forged, High Strength, Solid Steel Shanks are 1-1/8" To 1-1/16" Square and Are Welded To a High Carbon Steel Cutting Edge.
  • The Replaceable Tips are 1-3/4" wide.
  • This is a Severe Duty Toothbar! It Will Make a Big Improvement in Digging and Clean Up, and Will Dramatically Improve the Efficiency of Your Tractors Loader Work - You'll Wonder Why You Waited So Long To Get One!
  • Toothbar is shown Attached to a Bucket for Reference Only - The Bucket is NOT Included!
  • This Toothbar Is Intended To Be Used For Dirt, Soft & Loamy To Dry, Hard Conditions, Even With "Some" Rock & Gravel Content. It Is Not Intended To Be Used In Frozen Ground Conditions, Or In Packed, HI-Content Rocky Or Graveled Conditions!
  • Toothbar Weighs about 72lb's.

Make Sure Your Selection Is Based On The "INSIDE DIMENSION" Of Your Loaders Bucket! If You Need Help With Your Selection, Call Us At The Number Below!

Plus We're Glad To Say These Toothbars Are MADE IN THE USA!

Farm Equipment 24-7
Online Store of Iowa Farm Equipment
Providing Parts & Warranty Coverage Nationwide!

Share your knowledge of this product with other customers... Be the first to write a review